Whirlpool Range W10531342A User Manual

INSTALLATION INSTRUCTIONS  
20" (50.8 CM) FREESTANDING GAS RANGE  
with Standard Clean Oven  
Table of Contents  
RANGE SAFETY............................................................................. 2  
INSTALLATION REQUIREMENTS ............................................... 4  
Tools and Parts............................................................................ 4  
Location Requirements ............................................................... 4  
Electrical Requirements............................................................... 5  
Gas Supply Requirements .......................................................... 6  
INSTALLATION INSTRUCTIONS ................................................. 7  
Unpack Range............................................................................. 7  
Install Anti-Tip Bracket ................................................................ 7  
Make Gas Connection................................................................. 8  
Verify Anti-Tip Bracket Is Installed and Engaged ....................... 9  
Level Range............................................................................... 10  
Installing/Replacing the Battery ................................................ 10  
Battery Status Indicator............................................................. 11  
Electronic Ignition System......................................................... 11  
Complete Installation................................................................. 13  
GAS CONVERSIONS................................................................... 14  
LP Gas Conversion.................................................................... 14  
Complete Conversion................................................................ 16  
Natural Gas Conversion ............................................................ 16  
Complete Conversion................................................................ 18  
IMPORTANT:  
Save for local inspector's use.  
Installer: Leave installation instructions with the homeowner.  
Homeowner: Keep installation instructions for future reference.  
W10531342A  
 
In the State of Massachusetts, the following installation instructions apply:  
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by  
the State of Massachusetts.  
If using a ball valve, it shall be a T-handle type.  
A flexible gas connector, when used, must not exceed 3 feet.  
WARNING  
Tip Over Hazard  
A child or adult can tip the range and be killed.  
Install anti-tip bracket to floor or wall per installation instructions.  
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.  
Re-engage anti-tip bracket if range is moved.  
Do not operate range without anti-tip bracket installed and engaged.  
Failure to follow these instructions can result in death or serious burns to children and adults.  
To verify the anti-tip bracket is installed and engaged:  
Anti-Tip  
Bracket  
Slide range forward.  
Look for the anti-tip bracket securely attached to floor or wall.  
Slide range back so rear range foot is under anti-tip bracket.  
Range Foot  
See installation instructions for details.  
3
 
INSTALLATION REQUIREMENTS  
Tools and Parts  
Location Requirements  
Gather the required tools and parts before starting installation.  
Read and follow the instructions provided with any tools listed  
here.  
IMPORTANT: Observe all governing codes and ordinances. Do  
not obstruct flow of combustion and ventilation air.  
It is the installer’s responsibility to comply with installation  
clearances specified on the model/serial rating plate. The  
model/serial rating plate is located on the oven frame behind  
the left side of the broiler door.  
Tools needed  
Tape measure  
Marker or pencil  
Flat-blade screwdriver  
Phillips screwdriver  
Level  
Pipe-joint compound  
resistant to LP gas  
Noncorrosive leak-detection  
solution  
Hand or electric drill  
Wrench or pliers  
Pipe wrench  
For LP/Natural Gas  
Conversions  
A
³⁄₈" combination wrench  
½" combination wrench  
⁵⁄₈" combination wrench  
7 mm (⁹⁄₃₂") nut driver  
Quadrex®† or Phillips  
screwdriver  
¹⁵⁄₁₆" combination wrench  
¼" drive ratchet  
³⁄₈" nut driver  
A. Model/serial rating plate location  
The range should be located for convenient use in the  
kitchen.  
¹⁄₈" (3.2 mm) drill bit (for  
wood floors)  
Recessed installations must provide complete enclosure of  
the sides and rear of the range.  
Masking tape  
To eliminate the risk of burns or fire by reaching over heated  
surface units, cabinet storage space located above the  
surface units should be avoided. If cabinet storage is to be  
provided, the risk can be reduced by installing a range hood  
that projects horizontally a minimum of 5" (12.7 cm) beyond  
the bottom of the cabinets.  
Parts supplied  
Check that all parts are included.  
A
All openings in the wall or floor where range is to be installed  
must be sealed.  
B
Do not seal the range to the side cabinets.  
Cabinet opening dimensions that are shown must be used.  
Given dimensions are minimum clearances.  
The anti-tip bracket must be installed. To install the anti-tip  
bracket shipped with the range, see “Install Anti-Tip Bracket”  
section.  
Grounded electrical supply is required. See “Electrical  
Requirements” section. Proper gas supply connection must  
be available. See “Gas Supply Requirements” section.  
A. Anti-tip bracket  
B. #12 x 1⁵⁄₈" screws (2)  
Literature bag  
Contact a qualified floor covering installer to check that the  
floor covering can withstand at least 200°F (93°C).  
Conversion orifice spuds (inside bag containing literature)  
Use an insulated pad or ¼" (0.64 cm) plywood under range if  
installing range over carpeting.  
Anti-tip bracket must be securely mounted to floor or wall.  
Thickness of flooring may require longer screws to anchor  
bracket to floor.  
IMPORTANT: To avoid damage to your cabinets, check with your  
builder or cabinet supplier to make sure that the materials used  
will not discolor, delaminate or sustain other damage. This oven  
has been designed in accordance with the requirements of UL  
and CSA International and complies with the maximum allowable  
wood cabinet temperatures of 194°F (90°C).  
Parts needed  
9V DC alkaline battery (not included)  
Check local codes and consult gas supplier. Check existing gas  
supply and electrical supply. See “Electrical Requirements” and  
“Gas Supply Requirements” sections.  
†® QUADREX is a registered trademark of NLW Holdings, Inc.  
4
 
Mobile Home - Additional Installation Requirements  
Cabinet Dimensions  
The installation of this range must conform to the Manufactured  
Home Construction and Safety Standard, Title 24 CFR, Part 3280  
(formerly the Federal Standard for Mobile Home Construction  
and Safety, Title 24, HUD Part 280). When such standard is not  
applicable, use the Standard for Manufactured Home  
Cabinet opening dimensions shown are for 25" (64.0 cm)  
countertop depth, 24" (61.0 cm) base cabinet depth and 36"  
(91.4 cm) countertop height.  
Installations, ANSI A225.1/NFPA 501A or with local codes.  
If the cabinet depth is greater than 24" (61.0 cm), oven frame  
must extend beyond cabinet fronts by ½" (1.3 cm) minimum.  
Mobile home installations require:  
When this range is installed in a mobile home, it must be  
secured to the floor during transit. Any method of securing  
the range is adequate as long as it conforms to the standards  
listed above.  
D
B
C
Product Dimensions  
Freestanding Range  
A
E
G
F
H
I
41¹¹⁄₁₂"  
(106.6 cm)  
K
J
A. 18" (45.7 cm) min. clearance upper side cabinet to countertop  
B. 13" (33.0 cm) max. upper cabinet depth  
C. 20" (50.8 cm) min. cabinet opening width  
D. For minimum clearance to top of cooktop, see NOTE.  
E. 20¹⁄₈" (51.1 cm) min. opening width  
F. This shaded area recommended for installation of gas pipe.  
G. 3" (7.6 cm) min. countertop space to side wall or other  
combustible material  
25⁷⁄₈"  
(65.9 cm)  
19³⁄₄"  
(50 cm)  
H. 10" (25.4 cm)  
I. 5¹⁄₂" (14 cm)  
J. 4" (10 cm)  
K. 2" (5.1 cm)  
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal  
cabinet is covered by not less than ¹⁄₄" (0.64 cm) flame retardant  
millboard covered with not less than No. 28 MSG sheet steel,  
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or  
0.020" (0.5 mm) copper.  
30" (76.2 cm) minimum clearance between the top of the cooking  
platform and the bottom of an uncovered wood or metal cabinet.  
IMPORTANT: If installing a range hood or microwave hood  
combination above the range, follow the range hood or  
microwave hood combination installation instructions for  
dimensional clearances above the cooktop surface.  
Electrical Requirements  
This range is equipped with an electronic ignition system that  
works with an 9V DC alkaline battery (not included). See the  
“Installing/Replacing Battery” section for instructions on installing  
and replacing the battery.  
5
 
Gas Supply Requirements  
Flexible metal appliance connector:  
If local codes permit, a new CSA design-certified, 4-5 ft  
(122-152.4 cm) long, ½" (1.3 cm) or ¾" (1.9 cm) I.D.,  
flexible metal appliance connector may be used for  
connecting range to the gas supply line.  
WARNING  
A ½" (1.3 cm) male pipe thread is needed for connection  
to the female pipe threads of the inlet to the appliance  
pressure regulator.  
Explosion Hazard  
Use a new CSA International approved gas supply line.  
Install a shut-off valve.  
Do not kink or damage the flexible metal tubing when  
moving the range.  
Securely tighten all gas connections.  
Rigid pipe connection:  
If connected to LP, have a qualified person make sure  
gas pressure does not exceed 14" (36 cm) water  
column.  
The rigid pipe connection requires a combination of pipe  
fittings to obtain an in-line connection to the range. The rigid  
pipe must be level with the range connection. All strains must  
be removed from the supply and fuel lines so range will be  
level and in line.  
Examples of a qualified person include:  
licensed heating personnel,  
authorized gas company personnel, and  
authorized service personnel.  
Failure to do so can result in death, explosion, or fire.  
Observe all governing codes and ordinances.  
Must include a shutoff valve:  
IMPORTANT: This installation must conform with all local codes  
and ordinances. In the absence of local codes, installation must  
conform with American National Standard, National Fuel Gas  
Code ANSI Z223.1 - latest edition.  
The supply line must be equipped with a manual shutoff  
valve. This valve should be located in the same room but  
external to the range opening, such as an adjacent cabinet. It  
should be in a location that allows ease of opening and  
closing. Do not block access to shutoff valve. The valve is for  
turning on or shutting off gas to the range.  
IMPORTANT: Leak testing of the range must be conducted  
according to the manufacturer’s instructions.  
Type of Gas  
Natural gas:  
B
This range is design-certified by CSA International for use with  
Natural gas or, after proper conversion, for use with LP gas.  
A
This range is factory set for use with Natural gas. See “Gas  
Conversions” section. The model/serial rating plate located  
on the oven frame behind the left side of the broiler door has  
information on the types of gas that can be used. If the types  
of gas listed do not include the type of gas available, check  
with the local gas supplier.  
C
A. Gas supply line  
B. Shutoff valve “open” position  
C. To range  
LP gas conversion:  
Conversion must be done by a qualified service technician.  
Gas Pressure Regulator  
No attempt shall be made to convert the appliance from the gas  
specified on the model/serial rating plate for use with a different  
gas without consulting the serving gas supplier. See “Gas  
Conversions” section.  
The gas pressure regulator supplied with this range must be  
used. The inlet pressure to the regulator should be as follows for  
proper operation:  
Natural gas:  
Gas Supply Line  
Minimum pressure: 5" WCP  
Maximum pressure: 14" WCP  
LP gas:  
Minimum pressure: 11" WCP  
Maximum pressure: 14" WCP  
Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the  
range location. A smaller size pipe on longer runs may result  
in insufficient gas supply. With LP gas, piping or tubing size  
can be ½" (1.3 cm) minimum. Usually, LP gas suppliers  
determine the size and materials used in the system.  
Contact local gas supplier if you are not sure about the inlet  
pressure.  
NOTE: Pipe-joint compounds that resist the action of LP gas  
must be used. Do not use TEFLON®† tape.  
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.  
6
 
Line pressure testing above ½ psi gauge (14" WCP)  
Burner Input Requirements  
The range and its individual shutoff valve must be disconnected  
from the gas supply piping system during any pressure testing of  
that system at test pressures in excess of ½ psi (3.5 kPa).  
Input ratings shown on the model/serial rating plate are for  
elevations up to 2,000 ft (609.6 m).  
Line pressure testing at ½ psi gauge (14" WCP) or lower  
For elevations above 2,000 ft (609.6 m), ratings are reduced at a  
rate of 4% for each 1,000 ft (304.8 m) above sea level.  
The range must be isolated from the gas supply piping system by  
closing its individual manual shutoff valve during any pressure  
testing of the gas supply piping system at test pressures equal to  
or less than ½ psi (3.5 kPa).  
Gas Supply Pressure Testing  
Gas supply pressure for testing regulator must be at least 1"  
water column pressure above the manifold pressure shown on  
the model/serial rating plate.  
INSTALLATION INSTRUCTIONS  
Unpack Range  
Install Anti-Tip Bracket  
WARNING  
Excessive Weight Hazard  
WARNING  
Use two or more people to move and install range.  
Failure to do so can result in back or other injury.  
1. Do not use oven door handle to lift or move the range  
2. Remove shipping materials, tape and film from range. Keep  
Tip Over Hazard  
cardboard bottom under range.  
3. Remove oven racks and parts package from inside oven.  
A child or adult can tip the range and be killed.  
4. To place range on its back, take 4 cardboard corners from the  
carton. Stack one cardboard corner on top of another.  
Repeat with the other 2 corners. Place them lengthwise on  
the floor behind the range to support the range when it is laid  
on its back.  
Install anti-tip bracket to floor or wall per installation  
instructions.  
Slide range back so rear range foot is engaged in the  
slot of the anti-tip bracket.  
5. Using 2 or more people, firmly grasp the range and gently lay  
Re-engage anti-tip bracket if range is moved.  
it on its back on the cardboard corners.  
Do not operate range without anti-tip bracket installed  
and engaged.  
6. Pull cardboard bottom firmly to remove.  
7. Use an adjustable wrench to loosen the leveling legs. Adjust  
the leveling legs to the correct height. Leveling legs can be  
loosened to add up to a maximum of 1" (2.5 cm). A minimum  
of ³⁄₁₆" (0.5 cm) is needed to engage the anti-tip bracket.  
Failure to follow these instructions can result in death  
or serious burns to children and adults.  
NOTE: If height adjustment is made when range is standing,  
tilt the range back to adjust the front legs, then tilt forward to  
adjust the rear legs.  
1. Remove the anti-tip bracket from where it is attached inside  
the oven with a wire tie.  
2. Determine which mounting method to use: floor or wall.  
8. Place cardboard or hardboard in front of range. Using 2 or  
more people, stand range back up onto cardboard or  
hardboard.  
If you have a stone or masonry floor, you can use the wall  
mounting method. If you are installing the range in a mobile  
home, you must secure the range to the floor.  
7
 
3. Determine and mark centerline of the cutout space. The  
mounting can be installed on either the left side or right side  
of the cutout. Position mounting bracket against the wall in  
the cutout so that the V-notch of the bracket is 7⁷⁄₈" (20 cm)  
from centerline as shown.  
Make Gas Connection  
WARNING  
B
Centerline  
A
Explosion Hazard  
Use a new CSA International approved gas supply line.  
Install a shut-off valve.  
Securely tighten all gas connections.  
If connected to LP, have a qualified person make sure  
gas pressure does not exceed 14" (36 cm) water  
column.  
A. 7⁷⁄₈" (20 cm)  
B. Bracket V-notch  
4. Drill two ¹⁄₈" (3 mm) holes that correspond to the bracket  
holes of the determined mounting method. See the following  
illustrations.  
Examples of a qualified person include:  
licensed heating personnel,  
authorized gas company personnel, and  
authorized service personnel.  
Floor Mounting  
Failure to do so can result in death, explosion, or fire.  
Typical rigid pipe connection  
A combination of pipe fittings must be used to connect the range  
to the existing gas line. Your connections may be different,  
according to the supply line type, size and location.  
1. Apply pipe-joint compound made for use with LP gas to all  
pipe thread connections.  
Rear position  
Front position  
Diagonal (2 options)  
2. Using a pipe wrench to tighten, connect the gas supply to the  
range.  
Wall Mounting  
B
C
A
D
E
5. Using the Phillips screwdriver, mount anti-tip bracket to the  
wall or floor with the two #12 x 1⁵⁄₈" screws provided.  
F
6. Move range close enough to opening to allow for final gas  
and electrical connections. Remove shipping base,  
cardboard or hardboard from under range.  
G
7. Move range into its final location, making sure rear leveling  
leg slides into anti-tip bracket.  
A. Pressure regulator  
connection fitting  
B. 90° elbow  
D. Union  
E. Nipple  
F. Manual shutoff valve  
G. ½" or ¾" gas pipe  
C. Black iron pipe  
Typical flexible connection  
1. Apply pipe-joint compound made for use with LP gas to the  
smaller thread ends of the flexible connector adapters (see B  
and F in the following illustration).  
8. Move range forward onto shipping base, cardboard or  
hardboard to continue installing the range using the following  
installation instructions.  
2. Attach one adapter to the gas pressure regulator and the  
other adapter to the gas shutoff valve. Tighten both adapters.  
8
 
3. Use a combination wrench and pliers to attach the flexible  
connector to the adapters. Check that connector is not  
kinked.  
6. Remove cooktop burner caps and grates from parts  
package. Align notches in burner caps with pins in burner  
base. Burner caps should be level when properly positioned.  
If burner caps are not properly positioned, surface burners  
will not light. Place burners, burner caps and grates on the  
cooktop.  
A
B
Verify Anti-Tip Bracket Is Installed and  
Engaged  
D
1. Place the outside of your foot against the bottom front of the  
broiler, and grasp the lower right or left side of the control  
panel as shown.  
C
F
E
NOTE: If your countertop is mounted with a backsplash, it  
may be necessary to grasp the range higher than is shown in  
the illustration.  
G
H
A. Pressure regulator  
connection fitting  
B. Use pipe-joint compound.  
C. Adapter  
E. Adapter  
F. Use pipe-joint compound.  
G. Manual shutoff valve  
H. ½" or ¾" gas pipe  
D. Flexible connector  
Complete Connection  
1. Locate gas pressure regulator in the broiler.  
A
A. Gas pressure regulator  
IMPORTANT: Do not remove the gas pressure regulator.  
2. Slowly attempt to tilt the range forward.  
2. Check that the gas pressure regulator shutoff valve is in the  
If you encounter immediate resistance, the range foot is  
engaged in the anti-tip bracket.  
“ON” position.  
3. If the rear of the range lifts more than ½" (1.3 cm) off the floor  
without resistance, stop tilting the range and lower it gently  
back to the floor. The range foot is not engaged in the anti-tip  
bracket.  
IMPORTANT: If there is a snapping or popping sound when lifting  
the range, the range may not be fully engaged in the bracket.  
Check to see if there are obstructions keeping the range from  
sliding to the wall or keeping the range foot from sliding into the  
bracket. Verify that the bracket is held securely in place by the  
mounting screws.  
Front View  
Side View  
Front  
4. Slide the range forward, and verify that the anti-tip bracket is  
securely attached to the floor or wall.  
Shutoff valve  
“ON” Position  
5. Slide range back so the rear range foot is inserted into the  
3. Open the manual shutoff valve in the gas supply line. The  
slot of the anti-tip bracket.  
valve is open when the handle is parallel to the gas pipe.  
IMPORTANT: If the back of the range is more than 2" (5.1 cm)  
from the mounting wall, the rear range foot may not engage the  
bracket. Slide the range forward and determine if there is an  
obstruction between the range and the mounting wall. Changes  
to the gas supply must be performed by a qualified service  
technician. If you need assistance or service, refer to the  
“Assistance or Service” section of the Use and Care Guide for  
contact information.  
A
B
A. Closed valve  
B. Open valve  
4. Test all connections by brushing on an approved  
noncorrosive leak-detection solution. Bubbles will show a  
leak. Correct any leak found.  
5. Close the broiler door.  
9
 
6. Repeat steps 1 and 2 to ensure that the range foot is  
engaged in the anti-tip bracket.  
If the rear of the range lifts more than ½" (1.3 cm) off the floor  
without resistance, the anti-tip bracket may not be installed  
correctly. Do not operate the range without anti-tip bracket  
installed and engaged. Please reference the “Assistance or  
Service” section of the Use and Care Guide, or the cover or  
“Warranty” section of the User Instructions, to contact  
service.  
A
B
C
D
Level Range  
1. Place a standard flat rack in oven.  
2. Place level on the rack and check levelness of the range, first  
side to side; then front to back.  
A. Screw  
B. Metal battery top*  
C. Plastic battery box  
D. Battery holder  
3. If range is not level, pull range forward until rear leveling leg is  
*NOTE: Metal battery top is included in the bag containing  
removed from the anti-tip bracket.  
literature.  
4. Use a ³⁄₈" drive ratchet and slip-joint pliers to adjust leveling  
To install or replace the 9V DC alkaline battery, follow the steps  
below.  
legs up or down until the range is level.  
5. Push range back into position.  
1. Open the broiler door.  
2. Remove broiler pan and grill from broiler.  
6. Check that rear leveling leg is engaged in the anti-tip bracket.  
NOTE: Range must be level for satisfactory baking  
performance.  
3. Using a Phillips screwdriver, remove the metal battery top  
from the bottom of the range and open the plastic battery  
box.  
Installing/Replacing the Battery  
A
A. Battery holder location  
10  
 
4. Remove the battery holder and insert a new 9V DC alkaline  
Test the battery by lighting a burner. See “Electronic Ignition  
System” section. The electrode in each burner will spark and  
make a clicking noise.  
battery into it.  
When the battery needs to be replaced, follow these instructions  
and remove the old battery before inserting a new battery.  
Properly dispose of the old battery. See the “Battery Status  
Indicator” section to know when to replace the battery.  
Y
Battery Status Indicator  
T T E R  
B A  
The battery status indicator on the control panel will show the  
recommended time to replace the battery.  
5. Replace the battery holder in the plastic battery box with the  
battery facing the bottom and the blue wires facing up, and  
close the plastic battery box.  
Battery status indicator  
If the battery status indicator lights up red when any of the  
burner knobs is in the LITE position, then it is recommended  
you replace the battery with a new 9V DC alkaline battery.  
NOTE: If any knob is turned to the LITE position and there is no  
clicking noise or the battery status does not light, either the  
battery power is very low or completely discharged, or there is no  
battery connected to the battery case. In this event, replace the  
battery or install a new 9V DC alkaline battery.  
IMPORTANT: If the range will be unused for a long time, it is  
recommended that the battery is removed and stored out of reach  
of children. Reinstall the battery when the range will be used again.  
NOTE: Remove the battery before moving the range. Reinstall  
the battery after the range has been reconnected.  
While a knob is in the  
LITE position, if:  
Then:  
Battery status light is OFF The range is operating normally  
and igniters spark  
6. Reinstall the metal battery top and secure it with the screw.  
Battery status light is ON Change battery soon  
and igniters spark  
Battery status light is ON Change battery now  
and igniters do not spark  
Battery status light is OFF Change battery now or check to  
and igniters do not spark ensure battery is installed correctly  
Electronic Ignition System  
Initial lighting and gas flame adjustments  
Cooktop and oven burners use electronic igniters in place of  
standing pilots. When the cooktop control knob is turned to the  
“LITE” position, the system creates a spark to light the burner.  
This sparking continues until the control knob is turned to the  
desired setting.  
When the oven control knob is turned to the “LITE” position, the  
system creates a spark to light the pilot. The oven bottom has a  
hole to view the pilot. If the pilot is already lit, turn the oven control  
knob counterclockwise to completely light the oven burner.  
IMPORTANT: Do not operate bake burner without the metal  
battery top installed and secured.  
7. Replace the broiler pan and grill in the broiler rack.  
8. Close the broiler door.  
The electronic ignition system requires a 9V DC alkaline battery  
to create a spark to light the burners (this battery is not included).  
11  
 
Check Operation of Cooktop Burners  
Check Operation of Oven/Broil Burner  
1. If control panel and knobs were removed earlier, reinstall  
1. Open the oven door  
knobs.  
2. Press in and turn the oven control knob to the “LITE” position  
2. Push in and turn each surface unit control knob to the “LITE”  
position. The flame should light within 4 seconds.  
F
F
O
LITE  
LO  
I
H
MED  
The oven burner should light in 20-40 seconds; this delay  
is normal. The oven valve requires a certain time before it  
will open and allow gas to flow.  
3. Turn control knob to the “HI” position after burner lights.  
4. Check each cooktop burner for proper flame. The small inner  
cone should have a very distinct blue flame ¼" (0.64 cm) to  
½" (0.13 cm) long. The outer cone is not as distinct as the  
inner cone.  
To avoid damaging the oven igniter system, do not insert any  
object into the electrode system. Do not clean that area.  
3. Check the oven burner for proper flame. The flame should be  
½" (0.13 cm) long, with inner cone of bluish-green. The outer  
mantle should be dark blue and should be clean and soft in  
character. No yellow tips (not enough air), blowing or lifting  
(too much air) of flame should occur.  
A
B
If the flame needs adjusting:  
1. Turn the oven off. Wait for the oven burner to cool down.  
2. Open oven door and remove oven racks, oven tray, and flame  
A. Outer cone  
B. Inner cone  
spreader and set aside.  
5. Turn the control knob quickly to the “LO” position after the  
burner lights. If the flame goes out, turn the control knob to  
the “OFF” position.  
A
6. Check each cooktop burner for proper low flame. The low  
flame should be a minimum, steady blue flame. The flame  
size should be ¼" to ³⁄₈" (0.64 cm to 0.95 cm) high.  
A
C
If the low flame needs adjusting:  
1. With the burner flame on, turn control knob to the “LO”  
position and remove control knob.  
2. Insert a small flat-blade screwdriver into the valve stem. Turn  
the valve adjusting screw to obtain the smallest flame that will  
not go out when the control of a cold burner is quickly turned  
from “HI” to “LO.” Turn right to decrease flame height. Turn  
left to increase flame height. Repeat for other cooktop  
burners as needed.  
B
A. Oven tray (lift up at area shown to remove)  
B. Screws  
C. Flame spreader  
3. Locate the air shutter near the rear wall of oven and loosen  
the shutter screw.  
A
B
A
A. Valve stem  
A. Shutter screw  
B. Air shutter  
3. Replace control knob.  
4. Adjust the air shutter.  
5. Turn the oven back on and check for proper flame. If the  
flame is still not properly adjusted, turn the oven off, wait for  
the oven burner to cool down and repeat Step 4 until flame is  
properly adjusted.  
12  
 
6. When the flame has been properly adjusted, turn the oven off  
If range does not operate, check the following:  
and wait for the burner to cool down.  
9V DC alkaline battery is installed correctly.  
9V DC alkaline battery is not defective or discharged.  
9V DC alkaline battery is connected.  
7. Tighten the shutter screw.  
8. Reinstall flame spreader and oven tray. Reinstall the oven  
racks.  
See the “Troubleshooting” section of the Use and Care  
Guide.  
9. Close the oven door.  
10. Close the broiler door.  
8. When the range has been on for 5 minutes, check for heat. If  
the range is cold, turn off the range and check that the gas  
supply line shutoff valve is open.  
Complete Installation  
1. Check that all parts are now installed. If there is an extra part,  
If the gas supply line shutoff valve is closed, open it, then  
repeat the 5-minute test as outlined above.  
go back through the steps to see which step was skipped.  
2. Check that you have all of your tools.  
3. Dispose of/recycle all packaging materials.  
4. Check that the range is level. See the “Level Range” section.  
If the gas supply line shutoff valve is open, turn to  
“closed” position and contact a qualified technician.  
If you need Assistance or Service:  
5. Use a mild solution of liquid household cleaner and warm  
water to remove waxy residue caused by shipping material.  
Dry thoroughly with a soft cloth. For more information, see  
the “Range Care” section of the Use and Care Guide.  
Please reference the “Assistance or Service” section of the Use  
and Care Guide or contact the dealer from whom you purchased  
your range.  
6. Read the Use and Care Guide.  
7. Turn on surface burners and oven. See the Use and Care  
Guide for specific instruction on range operation.  
13  
 
GAS CONVERSIONS  
LP Gas Conversion  
WARNING  
WARNING  
Explosion Hazard  
Use a new CSA International approved gas supply line.  
Install a shut-off valve.  
Securely tighten all gas connections.  
Tip Over Hazard  
If connected to LP, have a qualified person make sure  
gas pressure does not exceed 14" (36 cm) water  
column.  
A child or adult can tip the range and be killed.  
Install anti-tip bracket to floor or wall per installation  
instructions.  
Examples of a qualified person include:  
Slide range back so rear range foot is engaged in the  
slot of the anti-tip bracket.  
licensed heating personnel,  
authorized gas company personnel, and  
authorized service personnel.  
Re-engage anti-tip bracket if range is moved.  
Do not operate range without anti-tip bracket installed  
and engaged.  
Failure to do so can result in death, explosion, or fire.  
Gas conversions from Natural gas to LP gas or from LP gas to  
Natural gas must be done by a qualified installer.  
Failure to follow these instructions can result in death  
or serious burns to children and adults.  
To Convert Gas Pressure Regulator  
1. Turn manual shutoff valve to the “closed” position.  
B
A
C
A. Gas supply line  
B. Manual shutoff valve “closed” position  
C. To range  
2. Unplug range or disconnect power.  
3. Open broiler door and remove broiler pan. The gas pressure  
regulator is located in the back right hand corner of the broiler  
compartment.  
A
A. Gas pressure regulator  
IMPORTANT: Do not remove the gas pressure regulator.  
14  
 
4. Remove the cap from the gas pressure regulator using a  
4. Install LP gas orifice spuds using a 7 mm combination  
flat-blade screwdriver.  
wrench.  
NOTE: Do not remove the spring beneath the cap.  
A
A
B
A. Cap  
5. Turn the cap over so the LP is visible.  
A
A. Spud  
B. Holder  
NOTE: This range cooktop is equipped with 2 standard  
burners and 2 super burners. Spud size and location remain  
the same.  
A. Cap  
6. Reinstall the cap.  
To Convert Surface Burners  
1. Remove burner grate, burner caps and burners.  
A
Standard  
Burner 78  
Super  
Burner 88  
B
Super  
Burner 88  
Standard  
Burner 78  
A. Burner cap  
B. Burner  
2. Locate LP gas orifice spuds for top burners in the literature  
bag included with the range. Two LP gas spuds are stamped  
“88” and two “78.”  
5. Place the Natural gas orifice spuds in the parts bag for future  
3. Remove Natural gas orifice spuds using a 7 mm combination  
use and keep with the bag containing literature.  
wrench.  
6. Reinstall burners, burner caps and burner grates.  
15  
 
To Convert Oven Burner  
Natural Gas Conversion  
1. Open the oven door and remove oven racks, oven tray and  
flame spreader and set aside.  
WARNING  
2. Lift oven burner. The orifice spud is behind the oven burner  
air shutter.  
Tip Over Hazard  
A
B
A child or adult can tip the range and be killed.  
A. Oven burner  
B. Air shutter  
Install anti-tip bracket to floor or wall per installation  
instructions.  
3. Locate LP gas orifice spud stamped “58” in the package  
Slide range back so rear range foot is engaged in the  
slot of the anti-tip bracket.  
containing literature supplied with the range.  
4. Use a ³⁄₈" combination wrench and remove the Natural gas  
Re-engage anti-tip bracket if range is moved.  
orifice spud.  
Do not operate range without anti-tip bracket installed  
and engaged.  
5. Install the number “58” LP gas spud.  
IMPORTANT: Do not overtighten.  
Failure to follow these instructions can result in death  
or serious burns to children and adults.  
A
To Convert Gas Pressure Regulator  
1. Turn manual shutoff valve to the “closed” position.  
A. LP oven orifice spud stamped with “58”  
B
6. Place Natural gas oven burner spud in plastic parts bag along  
with Natural gas cooktop burner spuds for future use and  
keep with the package containing literature.  
A
C
7. Reinstall oven burner.  
8. Reinstall oven racks, oven tray and flame spreader.  
A. Gas supply line  
B. Manual shutoff valve “closed” position  
C. To range  
Complete Conversion  
1. Refer to the “Make Gas Connection” section for properly  
2. Unplug range or disconnect power.  
connecting the range to the gas supply.  
3. Open broiler door and remove broiler pan. The gas pressure  
regulator is located in the back right hand corner of the broiler  
compartment.  
2. Turn the manual shutoff valve in the gas supply line to the  
“open” position.  
3. Refer to “Check Operation of Cooktop Burners” in the  
“Electronic Ignition System” section for proper burner  
ignition, operation and burner flame adjustments.  
A
IMPORTANT: You may have to adjust the “Lo” setting for  
each cooktop burner.  
Checking for proper cooktop and oven burner flames is very  
important. The small inner cone should have a very distinct  
blue flame ¼" to ½" (0.6 cm to 1.3 cm) long. The outer cone  
is not as distinct as the inner cone. LP gas flames have a  
slightly yellow tip.  
A. Gas pressure regulator  
4. Close the oven door and turn the knob to the “OFF” position.  
IMPORTANT: Do not remove the gas pressure regulator.  
5. Refer to the “Complete Installation” section to complete this  
procedure.  
16  
 
4. Remove the cap from the gas pressure regulator using a  
4. Install the Natural gas orifice spuds using a 7 mm  
flat-blade screwdriver.  
combination wrench.  
NOTE: Do not remove the spring beneath the cap.  
A
A
A. Cap  
5. Turn the cap over so that N or NAT is visible.  
B
A
A. Spud  
B. Holder  
NOTE: This range is equipped with 2 standard burners and  
2 super burners. Spud size and location remain the same.  
A. Cap  
6. Reinstall the cap.  
To Convert Surface Burners  
1. Remove burner grate, burner caps and burners.  
A
Standard  
Super  
Burner 125  
Burner 149  
B
Super  
Standard  
Burner 149  
Burner 125  
A. Burner cap  
B. Burner  
2. Locate the Natural gas orifice spuds for top burners in the  
package containing literature included with the range. Two  
Natural gas spuds are stamped “149” and two “125.”  
5. Place LP gas orifice spuds in the parts bag for future use and  
keep with the package containing literature.  
3. Remove the LP gas orifice spuds using a 7 mm combination  
6. Reinstall burners, burner caps and burner grates.  
wrench.  
17  
 
To Convert Oven Burner  
Complete Conversion  
1. Refer to the “Make Gas Connection” section for properly  
1. Open the oven door and remove oven racks, oven tray, and  
connecting the range to the gas supply.  
flame spreader and set aside.  
2. Turn the manual shutoff valve in the gas supply line to the  
2. Lift oven burner. The orifice spud is behind the oven burner  
“open” position.  
air shutter.  
3. Refer to “Check Operation of Cooktop Burners” in the  
“Electronic Ignition System” section for proper burner  
ignition, operation and burner flame adjustments.  
IMPORTANT: You may have to adjust the “Lo” setting for  
each cooktop burner.  
Checking for proper cooktop and oven burner flames is very  
important. The small inner cone should have a very distinct  
blue flame ¼" to ½" (0.6 cm to 1.3 cm) long. The outer cone  
is not as distinct as the inner cone. Natural gas flames do not  
have yellow tips.  
A
B
A. Oven burner  
B. Air shutter  
4. Close the oven door and turn the knob to the “OFF” position.  
3. Locate Natural gas orifice spud stamped “51” in the package  
5. Refer to the “Complete Installation” section to complete this  
containing literature supplied with the range.  
procedure.  
4. Use a ³⁄₈" combination wrench and remove the LP gas orifice  
spud.  
5. Install the number “51” LP gas spud.  
A
A. Natural gas oven orifice spud stamped with “51”  
IMPORTANT: Do not overtighten.  
6. Place LP gas oven burner spud in plastic parts bag along  
with LP gas cooktop burner spuds for future use and keep  
with the bag containing literature.  
7. Reinstall oven burner.  
8. Reinstall oven racks, oven tray and flame spreader.  
18  
 
Notes  
19  
 
W10531342A  
© 2012 Whirlpool Corporation.  
All rights reserved.  
9/12  
Printed in Mexico  
 

Weslo Treadmill WCTL396070 User Manual
Westinghouse Video Game Sound System UM100BK User Manual
Whirlpool Cooktop 8285116 User Manual
Whirlpool Dehumidifier AD25B User Manual
Whirlpool Freezer 2314466 User Manual
Xantech Stereo Receiver ML85 User Manual
Xantech Universal Remote MX88AI User Manual
Xantrex Technology Power Supply XPH 35 4D User Manual
Zanussi Freezer 727009 User Manual
Zanussi Washer ZWQ 5100 User Manual